Home News

How To Maintain Maser Marking Machine In Summer?

Certification
China Riselaser Technology Co., Ltd certification
China Riselaser Technology Co., Ltd certification
Customer Reviews
Thanks for packaging.Your packages are well designed and prepared carefully. Looks fine!

—— Gustavo

Thank you, Zoe. I just let you know I was quoting around 5 people about laser source. There were cheaper offers but I choose you in the end. I like your company especially the service.

—— Victor

The machine looks sturdy...well built.. like it!

—— Stefano

I'm Online Chat Now
Company News
How To Maintain Maser Marking Machine In Summer?

In summer, the temperature rises everywhere, and the laser marking machine will appear heating phenomenon in the process of using, which leads to some failures. Therefore, in summer to avoid laser marking machine failure in use, we must pay attention to the maintenance and repair of laser marking machine, so as to extend the service life of the machine.

To the summer solstice, the weather gradually turn hot, the temperature also rises. Summer is coming, Chongqing Renbao laser reminds you that you should take heatstroke prevention measures whether you are going out to play or working outdoors. We should not only prepare for heatstroke, but also maintain the laser marking machine to prevent the machine from "heatstroke".

1. Water-Cooling

The weather is hot and the deterioration rate of cooling water will be accelerated. It is suggested that users of laser marking machine use normal distilled water or pure water, and remove scale regularly to avoid the influence of laser power due to the scale attached to laser and pipeline; Note that the temperature of cooling water should not be too different from the air temperature. With the temperature increasing in summer, the working pressure of the cooling system of laser marking machine increases dramatically. It is suggested to check that the temperature of cooling water is too different from the air temperature before the high temperature comes. With the temperature increasing, the working pressure of the cooling system of laser marking machine increases dramatically, It is suggested to check and maintain the internal pressure of the cooling machine before the high temperature comes, adjust it to the high temperature environment in time, so as to make the working pressure of the cooling system increase dramatically. It is suggested to check the internal pressure of the cooling machine before the high temperature comes, and adjust it to the high temperature weather properly.

2. Line

Check and replace aging wires, plugs, hose and connectors; Check whether the pin wires of each electrical component connector are loose, and tighten them in time, so as to avoid electrical appliances burning out and unstable signal transmission caused by poor contact.

3. Lubrication

Each guide rail shall be cleaned frequently to remove dust and other sundries to ensure the normal operation of laser equipment. Hang points frequently on the shelf. Adjust the time. The oil quality changes in spring and autumn were observed with a shortened time of 0.5-1 times. The working machinery in high temperature area should be improved oil grade properly, which is easy to change oil temperature, and oil should be filled properly to ensure that oil temperature is free of sundries. Carefully check the straightness of marking table, the track of laser marking machine, and the verticality of marking machine. If there is any abnormality, it shall be repaired and debugged in time. The guide plate should be cleaned and equipped with motor frequently, so that the machine is always in the best state, so that the machine can move better in operation, mark more accurately and the quality of the marked products is higher.

Each guide rail shall be cleaned frequently to remove dust and other sundries to ensure the normal operation of laser equipment. Hang points frequently on the shelf. Adjust the time. The oil quality changes in spring and autumn were observed with a shortened time of 0.5-1 times. The working machinery in high temperature area should be improved oil grade properly, which is easy to change oil temperature, and oil should be filled properly to ensure that oil temperature is free of sundries. Carefully check the straightness of marking table, the track of laser marking machine, and the verticality of marking machine. If there is any abnormality, it shall be repaired and debugged in time. The guide plate should be cleaned and equipped with motor frequently, so that the machine is always in the best state, so that the machine can move better in operation, mark more accurately and the quality of the marked products is higher.

Pub Time : 2021-06-25 11:08:00 >> News list
Contact Details
Riselaser Technology Co., Ltd

Contact Person: Mr. Alex Ren

Tel: 008613924641951

Fax: 86-755-2750-2701

Send your inquiry directly to us (0 / 3000)